Related documents, manuals and ebooks about What Is Type 3 Rip Rap
03-033/01-09 (Rip Rap) 02272-3 C. Upon completion of the filter bed preparation, the rip rap shall be dumped and handled into place to form a compact layer to a thickness as shown on the drawings.
Section 805—Rip Rap and Curbing Stone Page 3 h. The allowable tolerances for Type 2 Curb dimensions are as follows: Measurement Item Dimension & Tolerance
Stone dumped rip rap is designated on the Plans as Type 1 or Type 3 as defined in Subsection 805.2.01. 603.2.01 Delivery, Storage, and Handling General Provisions 101 through 150. 603.3 Construction Requirements 603.3.01 Personnel
rip-rap liner will be no less than sixteen (16) inches. CLASS 3 RIP-RAP No more than 10% of the stone will have a diameter greater than twenty two (22) inches; no more than 50% of the stone will have a diameter less than sixteen (1 6) inches; and no more
Stone Type The material used for riprap should be fieldstone or rough unhewn quarry stone. Stone should be hard, angular, ... RIP-3. durability requirements for the determined rock size. Some guidance in selecting filter fabric is given below.
(Type) Rip Rap C. Y. Title: Microsoft Word - 405 Rip Rap.doc Author: houle Created Date: 8/4/2009 10:50:44 AM ...
Rip Rap Specifications. Title: RRspecs.xls Author: Deborah Smith Created Date: 1/22/2009 4:08:09 PM ...
€€€€€€€€€€€€ 1.3 Erosion Mechanisms and Riprap Failure Modes €€€€€€€€ Chapter 2 : HEC 11 Revetment Types €€€€€€€€€€€€ 2.1 Riprap ... Retaining Wall, Batter Type ...
4” to 20” RIP- RAP: Section 609.60.2.3 Type 3 Rock Ditch Liner shall consist of material with a predominant rock size of 12 inches (300 mm), a maximum rock size of 20 inches (500 mm) and a gradation such that no more than 15 percent will be less than 4 inches (100 mm).
All rock products, rip rap, boulders and soils are sold by the ton. All mulches and plant mixes are sold by cubic yard. 1 Ton/Cy of the material listed below at a 3" depth will cover square feet Concrete Sand 86 Sq. Ft. Squeege 83 Sq. Ft.
126.96.36.199 Item Type A .....5 188.8.131.52 Item Type B ... 5.3 Temporary Use of Stone Filling and Rip-Rap Items.....9 5.4 Disposal of Unacceptable Stockpiles ...
If no rip rap type has been selected, then "Class A" rip rap type is automatically selected by default. The following is a list of text to placed with respect to what rip rap type has been selected.
Maintains current rip rap sizes for outlet velocities 8 fps and greater 2. Establishes new riprap size for outlet velocities up to 8 fps ... EC-3 Type B or the Class of EC-1 to be specified shall be based on the culvert design storm outlet velocity with the following velocity
PROCEDURE FOR CONTROL OF STONE FILLING & RIP RAP ITEMS. GCP-14. Revision #3. STATE OF NEW YORK. DEPARTMENT OF TRANSPORTATION. GEOTECHNICAL ... 1.1 General 3. 1.2 Item Type 3. 1.2.1 Definition of Item Type 3. 1.2.2. Assignment of Item Type 3. 2. STOCKPILE CONSTRUCTION 4. 2.1 Construction of ...
than 3 feet unless analysis of scour potential demonstrates the need for deeper installation. ... a riprap size and then determining the corresponding "n" value for the rip rapped channel from: n = 167 0. 0.0395 d 50 where d 50 ... Type of rock available is crushed stone. Solution:
with an ELE Schmidt L-Type Hammer, while concrete strength was measured with an ELE Concrete Testing Hammer. Rip-rap/armourstone description and revetment evaluation are based on ... discussed in Section 3.0. The rip-rap revetment should have the following
2.3 RIP RAP AND APRONS 2.31 Rock Rip Rap I n situations where velocities discharging from a drain are moderàte (~15 fps),. rock rip rap may be the most economical type of dissipator to construct. Aesthetically, the rock may blend into the natural environment.
any type of sizing device, necessary to produce the desired sizes. ... Table C-3 Graded Rip-Rap Stone Creek Banks Pipe Outlets Lakes & Shorelines Rivers Georgia Department of Transportation GaSWCC c-3 . Table C-4 Filter Bedding Stone
4” to 20” Rip Rap: Type 3 (predominantly 12”) Meeting Specification 609.62.2.3 $ $ TOTAL ORDER EXTENSION: $ Delivery Time (A.R.O. = After Receipt of Order): A.R.O. SPECIFICATIONS All materials must comply with the quality and gradation requirements outlined within the 2011 Edition
plans for rip rap protection at the box culvert. 381+00.00 382+00.00 383+40.00 385+60.00 2" 2" 2 3/4" 17" hma surface course (2") hma surface removal ... material, type a, 4" existing profile embankment detail of profile change, us 136 section county fed. road dist. no. illinois fed. aid project ...
Rip Rap Type 1 Rip Rap Type 3 Rip Rap Type 1 A.R.E.M.A. #5 Rip Rap Type 3 Crusher Run Base Bank&Shore CERT FOR FDOTC32 GA178 Rip Rap Type 3 Crusher Run Base Graded Aggregate Base Course Bedding Stone Crusher Run Base
... Type L rip-rap shall be installed as shown in Figure 1202 and shall extend upstream and downstream from the bend a distance equal to the length of the ... 12.3 ENERGY DISSIPATERS. Where rip-rap structures are insufficient or uneconomical to control the erosion potential of storm runoff, ...
M. Rip rap shall be placed and stacked in manner that creates a stable slope that will not impede flow of water. ... Fill Type Class 6, from bottom of excavation to top of walls, compact uniformly to 97 percent of maximum density.
According to MNDOT standards, two types of geotextile are used for erosion control: 1. Type 3 or Lightweight - Used for rounded stone 2. Type 4 or Heavyweight – Used for sharp-edged stone
Rock or rip rap within the clear zone should be removed or moved outside the clear zone. If ... standard Type I curb and gutter with a modified 3” curb height. C. Bridge rails may have to be updated temporarily by placing retrofit bridge rail.
OBJECTIVE: Determine the rip rap sizing, gradation, and thickness for rip rap that will be placed on the landfill perimeter slopes. ... Draw the lower limit of the Type 3 filter material. This lower limit is subjective, but should provide a wide enough
TYPE 2A - BURIED GROUTED RIP-RAP DETAIL TYPE 2B - PNEUMATICALLY PLACED MOTAR DETAIL Continuous Turndown Along All Edges 6" Thick Colored Pneumatically ... EROSION PROTECTION - TYPE 2 SHEET 3 OF 3. Title: SD2515c.dwg Author: Bentley Systems, Inc. Created Date:
Rip Rap - Heavy Stone, Medium Stone, Dry, Select, Stackable. NYSDOT Subbase Type 3. NYSDOT Subbase Type 4. Crusher Run (Fine, 1 1/2" Max, 2 1/2" Max, 3 1/2" Max) CRUSHED GRAVEL: Washed Bituminous Sand #1 & #2 Gravel Blend. 1A Crushed Gravel (1/8" to 5/16")
Type 3 Surface Cr. 4 & 5 Surface Cr. Type 1 Binder Cr. Type 2 Binder Cr. Type 1 Asph. Agg. Base Cr. ... “PLACE 20 TONS OF RIP-RAP (CLASS B)” 3-5 . 12. Geotextile For Erosion Control Under RipRap Geotextile for erosion control is to be used under all Riprap.
g geotextile fabric (type iii) ... per cubic yard709-05.06 machined rip-rap (class a-1) per ton709-05.08 machined rip-rap (class b) per ton709-05.09 machined rip-rap (class c) per ton740-10.03 geotextile (type iii) (erosion control) ...
3. Type III channel a. Width at top of channel = 35 feet or greater. ... 3) Curve protected with rip-rap – 200 feet radius c. Paved concrete channel (cunette) required. Minimum width is 6 feet. d. Maximum paved or riprap side slope invert = 1/1 at depth established for 2-year frequency.
Page 3 Rip Rap SECTION VII - CONTROL AND PROTECTIVE MEASURES RESPIRATORY PROTECTION (SPECIFIC TYPE): NIOSH approved respirator is recommended. PROTECTIVE GLOVES: Rubber
Type 3 Rip Rap (Variable Depth) 220 Tons $ 255.21 $ 56,146.20 : 4 Type 3 Rip Rap (Variable Depth) 220: Tons $ 168.24 $ 37,012.80 5 HDPE Liner: 250 SY $ 40.00 $ 10,000.00 : 5 HDPE Liner: 250 SY $ 33.63 $ 8,407.50 : 5 HDPE Liner: 250 SY $ 25.38 ...
rip-rap outlet channel 7. underdrain 7a. house to underdrain connection 7b. standard pipe ... type b-1,b-2 & b-3, inlets (single) 13a. type ab-1" modified inlet 14. type b-1,b-2 & b-3, inlets (double) 15. storm drainage manhole 16. manhole frame and cover 17. sign mounting 18 ...
One part Type V portland cement, three parts aggregate by volume. The aggregate shall be two parts sand and one part 3/8 inch aggregate. ... specifications prior to placement of rock rip-rap. 3.2 Preparation of Ground Surfaces Trim and shape bed to provide even surfaces to the plan elevation.
EVALUATION AND PETROLOGIC CHARACTERISTICS OF FLORIDA RIP RAP SOURCES FINAL REPORT Sponsored by the Florida Department of Transportation State Contract No. BC354
level (SWL), these must be determined in order to find which type of wave (nonbreaking, breaking, or broken) the revetment will encounter. In many ... 1 = 3.5 ft. The depth db that initiates wave breaking directly against the
rip-rap (type 3) tn. 450.00. 72.00. 32,400.00. 90.00: 40,500.00 35.67: 16,051.50 100.00: 45,000.00 59.00: 26,550.00 4 #3 stone (rehab existing norfolk southern access) tn: 70.00. 68.00. 4,760.00. 50.00: 3,500.00 47.41: 3,318.70 45.00: 3,150.00 40.75: 2,852.50 5: silt fence (type c) (including ...
3. Project Name: Pebbly Beach Rip-Rap Slope Stabilization 4. Project Location: Avalon area, Santa Catalina Island, Los Angeles County Longitude Latitude -118.30943889000 33.33287852220 ... Type of Project: Repair of existing rip-rap slope 6.
Inlet slots shall be vane type, spaced every 6 inches. 2.07 Rip Rap A. Material: Field stone or crushed stone not to exceed 12 inches in diameter ... Rip Rap placement size and shape shall be Specified on the Detail Plate. 3.08 Field Quality Control A. General
3.1 Construction . B. ... Submittals shall show in detail the type, size, and location of all riprap to be used i. PA. RT 2 - PRODUCTS . ... Suitable rock from onsite excavation may be used as stone rip rap. Ro requirements identified above, as determin. PAR. T 3 - EXECUTIO. 3.
Changes in manhole type construction must be approved by the Engineer. B ... 3.4.3 Rip-Rap, Filter Blanket, and Filter Fabric – Measurement and payment of rip-rap, filter blanket, and filter fabric shall be in accordance with MNDOT 2511 except as modified or
f3 type 3 ramp f4 type 4 ramp f5 type 5 ramp - single f5a type 5 ramp - double f6 type 6 ramp f7 type 7 ramp ... e7 outlet protection - rip-rap e7a outlet protection - stilling basin e8 standard sediment trap e8a temporary sediment pond e10 diversion dike/swale
(Type) Rip Rap C.Y. Title: Microsoft Word - 405 Rip Rap_rev1005.doc Author: houle Created Date: 5/3/2010 4:20:50 PM ...
The governing criteria for the selection of the channel type are based on the hydraulic carrying capacity of the channel from the area runoff. 1. Type I Channel: ... 3) Curve protected with rip rap 75 feet radius c. Maximum side slope = 1 vertical to 3 horizontal. d. Minimum channel bottom = 4 ...
DETAIL ESTIMATING RIP RAP, ROCK PROTECTION AND GRANULAR SHEETING February 2014 Page 3 of 6 B511 If surface conditions, on which geotextile will be placed, are such that it is not
rip-rap as shown on the plans, specified herein, and/or directed by the ENGINEER. Any other erosion control ... and Type "C" material (unless otherwise shown on the pl ans). Rock channel protection shall have a minimum thickness (depth) ...
The spreading must be done by blower -type or other mulch -spreading equipment or by hand and anchored by pressing the ... Rip-rap shall b e hard, durable rock, concrete rubble, or similar material weighing at least 150 lbs per cubic foot.
To Rip Rap. ScourStop™ performs ... Deep Anchoring—a deadman-type anchor system utilizing a variable-length tether provides a secure ‘system attachment’ for slope stabilization 18 to 36 inches deep.
5 8. Approach Typical a) Lane and Shoulder widths b) Guardrail Type c) Road/Subbase Material 9. Rip Rap Header Details (if applicable) a) Toe Header Dimensions w/ geotextile liner